Difference between revisions of "ESP8266 / ESP8285"

From The TinkerNet Wiki
Jump to navigation Jump to search
Line 12: Line 12:
 
|+
 
|+
 
!GPIO
 
!GPIO
 +
!
 
!Input
 
!Input
 
!Output
 
!Output
Line 25: Line 26:
 
|-
 
|-
 
|ADC0
 
|ADC0
 +
|A0
 
|'''Analog Input'''
 
|'''Analog Input'''
 
|(not useable)
 
|(not useable)
Line 38: Line 40:
 
|-
 
|-
 
|0
 
|0
 +
|D3
 
|pulled up
 
|pulled up
 
|(caution)
 
|(caution)
Line 51: Line 54:
 
|-
 
|-
 
|1
 
|1
 +
|TX
 
|'''TX pin'''
 
|'''TX pin'''
 
|(caution)
 
|(caution)
Line 64: Line 68:
 
|-
 
|-
 
|2
 
|2
 +
|D4
 
|pulled up
 
|pulled up
 
|(caution)
 
|(caution)
Line 77: Line 82:
 
|-
 
|-
 
|3
 
|3
 +
|RX
 
|(caution)
 
|(caution)
 
|'''RX pin'''
 
|'''RX pin'''
Line 90: Line 96:
 
|-
 
|-
 
|4
 
|4
 +
|D2
 
|
 
|
 
|
 
|
Line 103: Line 110:
 
|-
 
|-
 
|5
 
|5
 +
|D1
 
|
 
|
 
|
 
|
Line 116: Line 124:
 
|-
 
|-
 
|6
 
|6
 +
|
 
|
 
|
 
|
 
|
Line 129: Line 138:
 
|-
 
|-
 
|7
 
|7
 +
|
 
|
 
|
 
|
 
|
Line 142: Line 152:
 
|-
 
|-
 
|8
 
|8
 +
|
 
|
 
|
 
|
 
|
Line 155: Line 166:
 
|-
 
|-
 
|9
 
|9
 +
|SD2
 
|
 
|
 
|
 
|
Line 168: Line 180:
 
|-
 
|-
 
|10
 
|10
 +
|SD3
 
|
 
|
 
|
 
|
Line 181: Line 194:
 
|-
 
|-
 
|11
 
|11
 +
|
 
|
 
|
 
|
 
|
Line 194: Line 208:
 
|-
 
|-
 
|12
 
|12
 +
|D6
 
|
 
|
 
|
 
|
Line 207: Line 222:
 
|-
 
|-
 
|13
 
|13
 +
|D7
 
|
 
|
 
|
 
|
Line 220: Line 236:
 
|-
 
|-
 
|14
 
|14
 +
|D5
 
|
 
|
 
|
 
|
Line 233: Line 250:
 
|-
 
|-
 
|15
 
|15
 +
|D8
 
|pulled to GND
 
|pulled to GND
 
|(caution)
 
|(caution)
Line 248: Line 266:
 
|-
 
|-
 
|16
 
|16
 +
|D1
 
|no interrupt
 
|no interrupt
 
|no PWM or I2C support
 
|no PWM or I2C support

Revision as of 14:07, 6 December 2020

ESP8266-Pinout.jpeg
ESP8266-Basic-circuit.png


ESP8266-symbol.png

Notes

  • IO13 & IO16 don't seem usable for I2C... (at least under Tasmota...)

GPIO Pins

GPIO Input Output Boot State Notes 01 01F M3 07 12 D1 mini
ADC0 A0 Analog Input (not useable) X X
0 D3 pulled up (caution) HSPI_MISO, I2SI_DATA connected to FLASH button, boot fails if pulled LOW
1 TX TX pin (caution) HIGH UART0_TXD debug output at boot, boot fails if pulled LOW
2 D4 pulled up (caution) HIGH? UART1_TXD boot fails if pulled LOW on-board LED on-board LED on-board LED
3 RX (caution) RX pin HIGH UART0_RXD
4 D2 often used as SDA (I2C) X
5 D1 IR_R often used as SCL (I2C) X X
6 connected to the flash chip X X X X X
7 connected to the flash chip X X X X X
8 connected to the flash chip X X X X X
9 SD2 HIGH connected to the flash chip X X X X X
10 SD3 HIGH connected to the flash chip X X X X X
11 connected to the flash chip X X X X X
12 D6 HSPI_MISO SPI (MISO) X X
13 D7 HSPI_MOSI, UART0_CTS SPI (MOSI) X
14 D5 HSPI_CLK SPI (SCLK) X
15 D8 pulled to GND (caution) LOW MTDO, HSPICS, UART0_RTS SPI (CS)

Boot fails if pulled HIGH

X X
16 D1 no interrupt no PWM or I2C support HIGH used to wake up from deep sleep X

Modules

Sonoff

Most (all?) of these are basically ESP8266 or ESP8285 controlled relays

Firmware

ESP8266 WiFi Connection manager

Original?

ESP8266 AT-Command firmware

Tasmota

Go Here!

Espruino

Home

ESPurna

Home

ESP-MQTT

Home

ESP-go

Home

NodeMcu

Home

ESP Easy

ESPHelper

Home

WLED

  • Home
    • Many bugs seem to appear with version changes...
      • 0.8.6 seems functional on my D1 Minis. (Tho it self-reports as 0.8.4)

Setting up Modules

  • ESP Boot Mode Controller.png
  • UMH3N Internals.png
  • ESP01 Programmed without button pressing.jpg

Booting The ESP82xx

Mode CH_PD (EN) RST GPIO15 GPIO0 GPIO2 TXD0
Download high high low low high high
Run high high low high high high

Communicating with the ESP8266

Physical Connection

Choose your favourite USB-Serial UART. (I like the CJMCU-340)

NOTE: The ESP8266 is a 3.3V device. Don't use a 5V UART!

GPIO1 = TxD

GPIO3 = RxD

As always, Connect TxD to RX-in on your UART & RxD to TX-out on your UART.

Talking to it

NOTE: The ESP initially spits out debug information at 74880 baud. This is not a standard speed. (some discussion about this)

Choose your favourite terminal program & point it at the appropriate port.

In this example, I'll use miniterm (Because it's simple)

  • miniterm.py /dev/ttyUSB0 74880

Gives me this (with an ESP-M3 that's been flashed & made ready for use...): 

--- Miniterm on /dev/ttyUSB0  74880,8,N,1 ---
--- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---

 ets Jan  8 2013,rst cause:1, boot mode:(3,6)

load 0x4010f000, len 3584, room 16 
tail 0
chksum 0xb0
csum 0xb0
v2843a5ac
~ld
␄␝␑␑␁"	��^�K␕���)␄5␑�␌7mX'\��o␇�␄5%�iHD��U␁'Rܥ@␁␒␕␝�␇!␕�␑t␅!o�Y��␓C����+��J[�`�␙��P␂�

See all that weirdness on the last few lines? That's data at a different speed. The device has booted & is trying to talk to us...

Starting over with:

  • miniterm.py /dev/ttyUSB0 115200

Gives me this: 

--- Miniterm on /dev/ttyUSB0  115200,8,N,1 ---
--- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
rd␀$��|␀�l�|␃␌␌␄�␄l�␄c|��␃�␒�;�cl␄c��g'�log���␌c␜8��lrl;lx�o�␘␃␌␄�␌d␌��␌␄␌#␄g�| 
␃�$�␄�#��no�␀$��l ␃�␛␓og␄l`␃␏␂'{���g␄␌c␃l`␃␇s��n␌␄c␂d`␂�c␌␄�␜␂�l{� ␃��o�␃
00:00:00 CFG: Loaded from flash at F9, Count 89
00:00:00 QPC: Count 2
00:00:00 Project tasmota ESP-M3-Everything-1 Version 8.5.0(tasmota)-2_7_4_1

Oh... Look. It's a Tasmota device.

Notice the weirdness between the banner & the first line with 00:00:00 at the start? That's the debug information coming in at 74880 that we saw in the previous example.

Interpreting the Debug Information

Here's the output from an ESP-07 that hasn't been flashed yet (IOW... Factory fresh): 

--- Miniterm on /dev/ttyUSB0  74880,8,N,1 ---
--- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---

 ets Jan  8 2013,rst cause:2, boot mode:(3,7)

load 0x40100000, len 27728, room 16 
tail 0
chksum 0x2a
load 0x3ffe8000, len 2124, room 8 
tail 4
chksum 0x07
load 0x3ffe8850, len 9276, room 4 
tail 8
chksum 0xba
csum 0xba
rf[112] : 00
rf[113] : 00
rf[114] : 01

SDK ver: 1.5.4(baaeaebb) compiled @ May 17 2016 19:23:54
phy ver: 972, pp ver: 10.1

)�L�

& the same device booted into flashing mode: 

--- Miniterm on /dev/ttyUSB0  74880,8,N,1 ---
--- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---

 ets Jan  8 2013,rst cause:2, boot mode:(1,7)

Notes on interpreting the Debug Information when things go wrong

Information Links

ESP8266 Datasheet
Esp8266 Hardware Design Guidelines
Kolban’s book on the ESP8266

Usage Links

 

Programming

Hardware

Ethernet

& More


Projects

Random

Bits & Pieces

Retrieved from ‘https://wiki.tinkernet.ca/index.php?title=ESP8266_/_ESP8285&oldid=1219’