IoT - ESP-M3 Everything! - Revision history

Tinker at 06:57, 24 January 2021

2021-01-24T06:57:56Z

Grant at 21:35, 5 November 2020

2020-11-05T21:35:38Z

Tinker at 14:52, 31 October 2020

2020-10-31T14:52:10Z

Tinker at 20:57, 20 October 2020

2020-10-20T20:57:55Z

Tinker at 20:50, 18 October 2020

2020-10-18T20:50:33Z

Tinker at 19:55, 18 October 2020

2020-10-18T19:55:45Z

Tinker at 19:13, 18 October 2020

2020-10-18T19:13:42Z

Tinker at 19:00, 18 October 2020

2020-10-18T19:00:37Z

Tinker at 16:41, 18 October 2020

2020-10-18T16:41:43Z

Tinker at 16:30, 18 October 2020

2020-10-18T16:30:31Z

← Older revision		Revision as of 06:57, 24 January 2021
Line 1:		Line 1:
		+	== '''OOPS!: The symbol & footprint currently in use has an error. The M3 does not break out GPIO13... It breaks out GPIO12. (One of these days, I'll get around to correcting that. For now, GPIO13 is actually GPIO12... :( )''' ==
	[[File:ESP-M3 Everything.png\|none\|thumb\|alt=\|This is the one that started it all...]]		[[File:ESP-M3 Everything.png\|none\|thumb\|alt=\|This is the one that started it all...]]

← Older revision		Revision as of 21:35, 5 November 2020
Line 6:		Line 6:

	[[:File:Esp-M3 Everything (gerbers).zip\|The Gerbers]] (Yup... you can get your own boards pretty quick & cheap)		[[:File:Esp-M3 Everything (gerbers).zip\|The Gerbers]] (Yup... you can get your own boards pretty quick & cheap)
		+
		+	NOTE: If using PCBWAY for production, the size for these boards needs to be input as 61mm x 36.6. If you use a slightly different (slightly rounder) number, they will charge you a dollar to change it. Just so you know.

	W00t! Boards are here!		W00t! Boards are here!

← Older revision		Revision as of 14:52, 31 October 2020
Line 1:		Line 1:
	[[File:ESP-M3 Everything.png\|none\|thumb\|alt=\|This is the one that started it all...]]		[[File:ESP-M3 Everything.png\|none\|thumb\|alt=\|This is the one that started it all...]]
		+
		+	This board carries the [[ESP-M3]] module.

	[[:File:ESP-M3 Everything (KiCAD).tar.gz\|The KiCAD files]]		[[:File:ESP-M3 Everything (KiCAD).tar.gz\|The KiCAD files]]

← Older revision		Revision as of 20:57, 20 October 2020
Line 69:		Line 69:

	'''''<big>YIPPEE!</big>'''''		'''''<big>YIPPEE!</big>'''''
		+	[[File:Populated M3 Testbed.jpg\|none\|thumb\|Fully populated as a testbed]]
		+	<br />

@@ Line 33: / Line 33: @@
 (10K at R2 may be a little bit of over-reaction to typical Chinese indicator LEDs...)
 [[File:Proper Power LED Brightness.jpg|none|thumb|alt=|Much better.  4K7 it is...]]
 [[File:Chinese vs Good.jpg|none|thumb|alt=|Comparing it to a typical Chinese power LED.]]

@@ Line 4: / Line 4: @@
 [[:File:Esp-M3 Everything (gerbers).zip|The Gerbers]] (Yup... you can get your own boards pretty quick & cheap)
 W00t!  Boards are here!
@@ Line 65: / Line 63: @@
 [[File:Tasmotized.png|none|thumb|Yup...  It's Tasmota]]
-[[File:Updated.png|none|thumb|Even managed an OTA update with no drama.]]
+[[File:Updated.png|none|thumb|Even managed an OTA update with no drama.]]At this point...

← Older revision		Revision as of 19:00, 18 October 2020
Line 52:		Line 52:
	[[File:Adaptor Usage.jpg\|none\|thumb\|alt=\|And tested the board using esptool.]]		[[File:Adaptor Usage.jpg\|none\|thumb\|alt=\|And tested the board using esptool.]]

−	[[File:Success.png\|none\|thumb\|alt=\|'''Yee Haw!''' Success!]]	+	[[File:Success.png\|none\|thumb\|alt=\|'''Yee Haw!''' Success!]]Tho... I suppose it'd be an idea to actually flash something to it & fully prove the point.
		+
		+	So:
		+
		+	<code>esptool.py erase_flash</code>
		+
		+	Followed by:
		+
		+	<code>esptool.py write_flash -fs 1MB -fm dout 0x0 tasmota.bin</code>
		+
		+	and...
		+	[[File:Tasmotized.png\|none\|thumb\|Yup... It's Tasmota]]
		+	<br />

@@ Line 11: / Line 11: @@
 [[File:ESP-M3 Everything (Physical)(Front).jpg|none|thumb]]
 [[File:ESP-M3 Everything (Physical)(Back).jpg|none|thumb]]
 This is gonna be a little bit fiddly...
-[[File:WTF was I thinking.jpg|none|thumb]]
+[[File:WTF was I thinking.jpg|none|thumb|alt=|This is gonna be a little bit fiddly...]]
 Here's the first attempt at the truly fiddly bits...
-[[File:Finger Crossing Time.jpg|none|thumb]]
+[[File:Finger Crossing Time.jpg|none|thumb|alt=|Here's the first attempt at the truly fiddly bits...]]
 Shall we see if it lives?
-[[File:Ready, set.jpg|none|thumb]]
+[[File:Ready, set.jpg|none|thumb|alt=|Shall we see if it lives?]]
-Nope :(
-[[File:Nope.jpg|none|thumb]]
+[[File:Nope.jpg|none|thumb|alt=|Nope :(]]
 .17V on Vcc seems wrong...
 Think I'll go ahead and suspect the connector isn't on there quite right.  Real bitch to hand solder.
-[[File:Semi-w00t.jpg|none|thumb]]
-Semi-w00t...  Feeding it 5V directly works just fine...
+[[File:Semi-w00t.jpg|none|thumb|alt=|Semi-w00t...]]
-[[File:Full-w00t.jpg|none|thumb]]
+Feeding it 5V directly works just fine...
-Full-w00t...  Just had to add flux & stick the tip of my iron under there to carefully reflow pin 1 of the USB connector.
-[[File:Teeny Parts - Non-teeny Tip.jpg|none|thumb]]
+[[File:Full-w00t.jpg|none|thumb|alt=|Full-w00t...]]
-It '''IS''', in fact, possible to do SMT work with normal gear...
+Just had to add flux & stick the tip of my iron under there to carefully reflow pin 1 of the USB connector.
 Notice that I had to take that picture with lots of shade so the LED would show up...  :(
 (10K at R2 may be a little bit of over-reaction to typical Chinese indicator LEDs...)
-[[File:Proper Power LED Brightness.jpg|none|thumb]]
+[[File:Proper Power LED Brightness.jpg|none|thumb|alt=|Much better.  4K7 it is...]]
 Much better.  4K7 it is...
-[[File:Chinese vs Good.jpg|none|thumb]]
+[[File:Chinese vs Good.jpg|none|thumb|alt=|Comparing it to a typical Chinese power LED.]]
-[[File:Ready for Next test.jpg|none|thumb]]
+[[File:Ready for Next test.jpg|none|thumb|alt=|Ready for the next test.]]
 At this point, the board is fully populated.
-[[File:It Lives!!!.jpg|none|thumb]]
-'''It's Alive!!!'''
+[[File:It Lives!!!.jpg|none|thumb|alt=|'''It's Alive!!!''']]
 Not enough hands to catch the bootup blink of the M3 in the picture, but it did flash.
@@ Line 50: / Line 50: @@
 Well... Off by a day, but I built [[IoT - ESP-Everything Programming adaptor|the programming adaptor]].
-And tested the board using esptool.
+[[File:Adaptor Usage.jpg|none|thumb|alt=|And tested the board using esptool.]]
-'''Yee Haw!'''  Success!
+[[File:Success.png|none|thumb|alt=|'''Yee Haw!'''  Success!]]

← Older revision		Revision as of 16:30, 18 October 2020
Line 1:		Line 1:
−	~~This is the one that started it all...~~	+	[[File:ESP-M3 Everything.png\|none\|thumb\|alt=\|This is the one that started it all...]]
−	[[File:ESP-M3 Everything.png\|none\|thumb]]

	[[:File:ESP-M3 Everything (KiCAD).tar.gz\|The KiCAD files]]		[[:File:ESP-M3 Everything (KiCAD).tar.gz\|The KiCAD files]]